flowblock.blogg.se - Cisco asr 1001 license lookup

#Cisco asr 1001 license lookup upgrade#
#Cisco asr 1001 license lookup software#
#Cisco asr 1001 license lookup code#

The image carries 2-count 10-GE port EvalRTU (Evaluation) licenses.

An End-User License Agreement (EULA) will be displayed for each port if there is no permanent license present to support these ports.

Count-based licenses will be used for 10-GE ports, 1 count per port.

The 10-GE interfaces on the Cisco ASR 1001-X Router use a per port counted license, which has the following features: Per Port Counted License (10-GE Interfaces) show license all Command Output Description StoreIndex: 13 Feature: interface_10g Version: 1.0 StoreIndex: 12 Feature: vpls Version: 1.0 StoreIndex: 11 Feature: throughput_20g Version: 1.0 StoreIndex: 10 Feature: throughput_10g Version: 1.0 StoreIndex: 9 Feature: throughput_5g Version: 1.0 License State: Active, Not in Use, EULA accepted StoreIndex: 8 Feature: sw_redundancy Version: 1.0 StoreIndex: 5 Feature: lawful_intr Version: 1.0 StoreIndex: 4 Feature: ipsec Version: 1.0 StoreIndex: 3 Feature: fwnat_red Version: 1.0 License State: Active, Not in Use, EULA not accepted

StoreIndex: 1 Feature: advipservices Version: 1.0 StoreIndex: 0 Feature: adventerprise Version: 1.0 License Count: 2/0/0 (Active/In-use/Violation) StoreIndex: 0 Feature: interface_10g Version: 1.0 The following example displays sample output from the show license all command: Primary License Storage stores the currently purchased and installed licenses. In the last 24 hours, sampling period is 300 seconds %BW_LICENSE-4-THROUGHPUT_MAX_LEVEL: SIP0: cpp_ha: Average throughput rateĪpproached the licensed bandwidth of 2000000000 bps during 1 sampling periods The configured throughput level in this example is 20 Gbps: System-forwarding plane approaches or exceeds the configured throughput license Will be displayed once every 24 hours if the traffic handled by the %IOSXE_THROUGHPUT-6-LEVEL: Throughput level has been set to 20000000 kbps Reboot level = adventerprise and License = adventerprise %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = asr1001x Next Reloaded, the log messages at the router startup will display the license-levelĪnd throughput-level information, for example: The current throughput level is 2000000 kb/s Router# show platform hardware throughput level

#Cisco asr 1001 license lookup upgrade#

Output from this command after you apply the 20 Gbps performance upgrade Show platform hardware throughput level command. You can upgrade the throughput of the ESP from any license level toĬurrent throughput level of the ESP, run the Throughput of the ESP from 2.5 Gbps (default) to 5 Gbps, 10 Gbps, or 20 Gbps byĪpplying a software-activated performance upgrade license and then reloading

#Cisco asr 1001 license lookup software#

Gbps (default), 5 Gbps, 10 Gbps, and 20 Gbps depending upon the software Service processor of the Cisco ASR 1001-X Router supports throughputs of 2.5 Indicates the current requested Cisco lOS license level to boot. show running-config Command Output Description The following example displays sample output from the show running-config command: Use the show running-config command or the show startup-config command to view the license-level information. Indicates the startup configuration definition that will be used for the next reload instance. That would indicate that the purchase of a license is required. Indicates whether you are utilizing a permanent (purchased) license, an evaluation 60-day license, or a Right-to-Use license

#Cisco asr 1001 license lookup code#

Indicates the current Cisco IOS license code level. Use the show version command to determine the Cisco IOS license level in the router.